D W Fearn VT1 Mono Tube PreAmp - the final run of the classic VT1

D W Fearn VT1 Mono Tube PreAmp - the final run of the classic VT1

Regular price £2,842.00
/

Only 2 items in stock!

The VT-series microphone preamplifiers will change the way you think of audio quality. The transparency is astounding. Vocals sound smoother, warmer, more intimate, with a compelling presence. Any microphone and any sound will benefit from the improved clarity, definition, and lack of solid-state artifacts.

The VT-series microphone preamplifiers will change the way you think of audio quality. The transparency is astounding. Vocals sound smoother, warmer, more intimate, with a compelling presence. Any microphone and any sound will benefit from the improved clarity, definition, and lack of solid-state artifacts. The VT-1 recreates the sound of classic tube preamps of the 1960s. Modern components and computer-optimized circuitry, unavailable during the vacuum tube era, elevate this design to a new level of performance.

The VT-1 is the single channel version of the D.W. Fearn VT-2 Vacuum Tube Microphone Preamplifier. The specifications are identical to the VT-2.

Feature:

  • all vacuum-tube design 
  • clean and airy high end 
  • fat low end 
  • unsurpassed warmth, transparency, and musicality 
  • Lo-Z input position for superior performance with transformerless mics 
  • Phase (polarity) reverse switch 
  • +48 volt phantom power (completely disconnected when off)
  • custom-design Jensen input and output transformers for superb sonics 
  • 20 dB input pad (switchable) 
  • true VU meters (amplifier isolated) 
  • all point-to-point audio wiring 
  • high-performance, fully-regulated power supplies with exceptional reserve 
  • gold input and output XLR connectors 
  • polypropylene and polystyrene coupling capacitors 
  • all audio switching through gold-contact, sealed precision relays 
  • international operation on 100, 120, or 220 VAC, 50/60 Hz 
  • CE certified, RoHS-compliant 
  • +4 dBm output
  • conservatively rated precision components and rugged construction for stability and long life
  • line-level processing with the LP-1 Line Padaccessory 
  • single-channel version D.W. Fearn VT-1 also available 
  • direct recording of electric instruments with the D.W. Fearn VT-3 Vacuum Tube DI or PDB Passive Direct Box 

SPECIFICATIONS

  • Input 150 ohms 
  • Input Load Impedance 1.5k ohms
  • Minimum Input Level -65 dBm nominal 
  • Maximum Input Level @ 20 cps -30 dBm without pad, -5 dBm with 20 dB pad 
  • Gain 53 dB 
  • Frequency Response +/-0.25 dB 20 cps to 20 kc; -3 dB @ 0.5 cps and 55 kc 
  • THD+Noise less than 0.25% 20 cps to 20 kc 
  • Intermodulation Distortion SMPTE less than 0.02% 
  • Signal to Noise Ratio 74 dB minimum 
  • Equivalent Input Noise -124 dBm maximum 
  • Output low-Z, transformer-balanced 
  • Maximum Output Level +22 dBm, 20k ohm load 
  • Power Requirements 100, 120, or 220 VAC, 50/60 Hz 
  • Dimensions 19" (48.26cm) W, 5.25" (13.34cm) H, 14" (35.56cm) D 
  • Weight 18 lbs (8.16kg)

NOTE: Frequency is specified in cycles per second (cps) or kilocycles per second (kc). These units correspond to Hz and kHz respectively. Measurements made with -50 dBm input and 50 dB gain in a 22 cps to 22 kc bandwidth. Specifications and price subject to change without notice. 

+ View more